Multivariate optimization and comparison between conventional extraction (CE) and ultrasonic-assisted extraction (UAE) of carotenoid extraction from cashew apple

Carotenoids are an essential component of cashew and can be used in pharmaceuticals, cosmetics, natural pigment, food additives, among other applications. The present work focuses on optimizing and comparing conventional and ultrasound-assisted extraction methods. Every optimization step took place with a 1:1 (w:w) mixture of yellow and red cashew apples lyophilized and ground in a cryogenic mill. A Simplex-centroid design was applied for both methods, and the solvents acetone, methanol, ethanol, and petroleum ether were evaluated. After choosing the extractor solvent, a central composite design was applied to optimize the sample mass (59–201 mg) and extraction time (6–34 min). The optimum conditions for the extractor solvent were 38% acetone, 30% ethanol, and 32% petroleum ether for CE and a mixture of 44% acetone and 56% methanol for UAE. The best experimental conditions for UAE were a sonication time of 19 min and a sample mass of 153 mg, while the CE was 23 min and 136 mg. Comparing red and yellow cashews, red cashews showed a higher carotenoid content in both methodologies. The UAE methodology was ca. 21% faster, presented a more straightforward composition of extracting solution, showed an average yield of superior carotenoid content in all samples compared to CE. Therefore, UAE has demonstrated a simple, efficient, fast, low-cost adjustment methodology and a reliable alternative for other applications involving these bioactive compounds in the studied or similar matrix.     

Advances of phononics in 2012—2022

Due to its great potential applications in thermal management, heat control, and quantum information, phononics has gained increasing attentions since the first publication in Rev. Mod. Phys. 84 1045 (2012). Many theoretical and experimental progresses have been achieved in the past decade. In this paper, we first give a critical review of the progress in thermal diodes and transistors, especially in classical regime. Then, we give a brief introduction to the new developing research directions such as topological phononics and quantum phononics. In the third part, we discuss the potential applications. Last but not least, we point out the outlook and challenges ahead.     

Effect of oxygen on regulation of properties of moderately boron-doped diamond films

Regulation of oxygen on properties of moderately boron-doped diamond films is fully investigated. Results show that, with adding a small amount of oxygen (oxygen-to-carbon ratio < 5.0%), the crystal quality of diamond is improved, and a suppression effect of residual nitrogen is observed. With increasing ratio of O/C from 2.5% to 20.0%, the hole concentration is firstly increased then reduced. This change of hole concentration is also explained. Moreover, the results of Hall effect measurement with temperatures from 300 K to 825 K show that, with adding a small amount of oxygen, boron and oxygen complex structures (especially B₃O and B₄O) are formed and exhibit as shallow donor in diamond, which results in increase of donor concentration. With further increase of ratio of O/C, the inhibitory behaviors of oxygen on boron leads to decrease of acceptor concentration (the optical emission spectroscopy has shown that it is decreased with ratio of O/C more than 10.0%). This work demonstrates that oxygen-doping induced increasement of the crystalline and surface quality could be restored by the co-doping with oxygen. The technique could achieve boron-doped diamond films with both high quality and acceptable hole concentration, which is applicable to electronic level of usage.     

电机驱动微装配在双光子制备微结构中的应用

对微结构的制作、微装配系统进行了研究. 采用飞秒激光双光子聚合微加工技术制作有底座、精细的三维立体“拱形”微结构, 其高250μm、长300μm、厚50μm. 将此微结构与实验室自主搭建的二维微装配平台相结合, 利用自主编程的人机交互界面驱动步进电机, 远程操控微装配设备; 将荧光闪烁陶瓷粉末装配到微结构中, 对装配后的微结构进行荧光光谱表征发现, 纯荧光粉末和微结构中的荧光粉末的发射光谱在测量误差范围内基本一致, 表明荧光粉末的光学性质未发生改变. 利用该装置可以将各类微纳米级材料和微结构进行装配, 形成含有不同材料的微结构系统.     

Quantized-states-based adaptive control against unknown slippage effects of uncertain mobile robots with input and state quantization

An adaptive tracking design strategy based on quantized state feedback is developed for uncertain nonholonomic mobile robots with unknown wheel slippage effects. All state variables and control torques are assumed to be quantized by the state and input quantizers, respectively, in a network control environment. Thus, the quantized state feedback information is only available for the tracking control design. An approximation-based adaptive controller using quantized states is recursively designed to ensure the robust adaptive tracking against unknown wheel slippage effects where the quantized-states-based adaptive mechanism is derived to compensate for unknown wheel slippage effects, system nonlinearities, and quantization errors. The boundedness of the quantization errors and estimated parameters in the closed-loop system is analyzed by presenting some theoretical lemmas. Based on these lemmas, we prove the uniform ultimate boundedness of closed-loop signals and the convergence of the trajectory tracking error in the presence of wheel slippage effects. Simulations verify the effectiveness of the resulting tracking scheme.     

A Closed‐Loop Control Strategy for Producing Nitrile Rubber of Uniform Chemical Composition in a Semibatch Reactor: A Simulation Study

To improve the quality of industrial nitrile rubbers, the copolymer chemical composition, p_A(t), should ideally be kept constant along the reaction. This work proposes a closed‐loop control strategy for the semibatch operation of the reactor with the aim of regulating p_A(t) within a reduced range of variability. The proposed strategy is evaluated by simulating a mathematical model of the process. To this effect, a simplified mathematical model of the reaction is first derived and then utilized to obtain a suboptimal control law and a soft‐sensor that estimates the polymerization rates. The suboptimal control law is compensated by adding a term proportional to errors in p_A(t). The simulated example considers the production of the low‐composition AJLT grade, with the copolymerization reaction represented by a detailed mathematical model adjusted to an industrial plant. Due to the high performance of the soft‐sensor, the simulation results suggest that the proposed closed‐loop strategy is efficient to adequately regulate p_A(t) in spite of structural and parametric uncertainties, while other quality variables remained practically unaffected.     

Wave-based vibration control of large cable net structures

Large cable net structures have been widely applied in aerospace engineering due to the feature of light-weight, high packaging efficiency, and high thermal stability. Structural vibrations induced by a variety of disturbances are inevitable in the space environment, resulting in the requirement of effective vibration control strategies for large cable net structures. Since the large cable net structures have many closely spaced vibrational modes in the range of low frequencies, traditional modal based control may cause modal truncation and spillover problems. In this paper, a wave-based boundary control strategy is adopted and its effectiveness to control the vibration of cable net structures is investigated, by transfer function analysis and numerical methods. It is found that the structural vibration can be absolutely resisted by applying the wave-based boundary controllers onto all the exterior nodes, when disturbances come from the external boundaries of the cable net. Our results in this paper can provide a theoretical basis for the vibration control of large cable net structures.     

Melting thermodynamics of oligonucleic acids conjugated with relatively solvophobic linear polymers: A coarse‐grained molecular simulation study

Oligonucleic acids (ONAs), such as DNA and RNA, are used in various biotechnology and nanotechnology applications due to their ability to form a double helix that is stable at low temperature and melts at high temperatures. The melting temperature (T_m) of ONA duplexes can be tuned by the ONA composition, sequence, length and concentration, solvent quality, and salt concentration and by conjugation to other macromolecules. In this article, we use coarse‐grained (CG) molecular simulations to study ONAs conjugated with linear homopolymers that are relatively more solvophobic than the ONA. We study charged and stiff 8‐mer ONAs (e.g., DNA) and neutral and flexible 8‐mer ONAs (e.g., peptide nucleic acids or PNA), and vary the composition (or G‐C content) and sequence of ONA, conjugated homopolymer lengths and solvent quality for the polymer. For neutral and flexible ONAs, as the solvent quality worsens for the polymer, the ONA melting temperature increases from that of unconjugated ONA. The melting curves broaden with polymer length and worsening solvent quality, especially for ONAs with higher G‐C content. For charged and stiff ONAs, as the solvent quality worsens, the ONA melting temperature decreases compared to unconjugated ONA while the width of the melting curve remains the same. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1196–1208